Best smart circuit breaker panels of 2026 replace or augment the dumb metal box in your utility room with something that meters and switches every circuit from your phone. I have researched these systems and spoken through the install with owners of two of them, and the honest finding is that the category splits cleanly: a full panel replacement is a big, expensive job that pays off when you are already replacing the panel or adding solar, a battery and an EV, while a retrofit controller is cheaper and better when your existing panel is healthy.
The second thing to understand is that a smart panel is not the same as an energy monitor. A monitor clamps onto the wires and reports usage. A smart panel replaces the breakers themselves, so it can turn individual circuits on and off, shed loads automatically when a battery is low, and manage an EV charger against the rest of the house. That control is the reason to spend the extra money, and it is also why the install is a real electrical job rather than a weekend project.
Prices below are US hardware and installed ranges captured in November 2026. They vary enormously with the job, because a simple swap in a cheap labour market is a different project from a swap plus a service-mast upgrade.
At a glance
| Product | Best for | Key specs | Installed price |
|---|---|---|---|
| Span Smart Panel | Best overall | 32 or 40 circuits, all metered and controlled, native solar and battery | About 6,500 to 10,000 USD |
| Leviton Smart Load Center | Best modular | Standard 200A panel, smart breakers added one at a time | About 3,500 to 7,500 USD |
| Schneider Square D Energy Center | Best inside a Schneider system | Up to 42 circuits with modular smart relays, Wiser app | About 3,000 to 5,150 USD hardware |
| Lumin Smart Panel | Best retrofit | 8 to 12 managed circuits beside your existing panel | About 3,000 to 8,000 USD |
| Eaton Brightlayer with Span software | Best for Eaton households | Every circuit metered and controlled using Span’s software | Quoted through an installer |
The best smart circuit breaker panels of 2026
1. Span Smart Panel, best overall
Span is the most complete smart panel and the one to buy if you are replacing the panel anyway. It is a full replacement with a digital busbar, available as the MAIN 32 and MAIN 40, and it meters and controls every circuit from the app rather than only the ones you fit with a smart breaker. It integrates natively with major solar and battery brands including Tesla, Enphase, SolarEdge and FranklinWH, sheds loads automatically when a battery is low, and manages an EV charger against the rest of the house. Hardware is about 2,550 to 4,100 USD depending on the model, with a typical installed cost of 6,500 to 10,000 USD, and it carries a 10-year warranty when installed by a Span authorized installer. The honest downsides are the price and the fact that it is a full panel swap with a permit and a utility disconnect, so it is the wrong choice if your current panel is fine.
Pros
- Every circuit metered and controlled, not just the smart ones
- Native integration with the major solar and battery brands
- 10-year warranty and automatic load shedding
Cons
- About 6,500 to 10,000 USD installed, the priciest here
- Full panel replacement with permit and utility disconnect
Check today’s price on Amazon.
2. Leviton Smart Load Center, best modular
Leviton takes the opposite approach, and it is the better fit for many homes. It is a conventional 200A load center that accepts Leviton’s second-generation smart breakers, so you buy a normal panel and add monitoring and control one circuit at a time as the budget allows. That keeps the entry cost down, suits a retrofit where only a few circuits matter, and lets an electrician add breakers later without replacing anything. The trade-off is that only the circuits fitted with a smart breaker are metered and controlled, so a whole-home view requires a hub and a full set of breakers. Installed prices run about 3,500 to 7,500 USD depending on the breaker count.
Pros
- Conventional panel with smart breakers added over time
- Lower entry cost than a full smart panel
- Any licensed electrician can install it, with no specialist certification
Cons
- Only smart-breaker circuits are monitored and controlled
- A whole-house setup with many breakers costs as much as a Span
Check today’s price on Amazon.
3. Schneider Square D Energy Center, best inside a Schneider system
Schneider’s Square D Energy Center, run through the Wiser app, is the pick if you are buying into the Schneider ecosystem of solar and storage. It is a full panel with modular smart relays on the busbar, handling up to 42 circuits, with branch-circuit current transformer metering and smart relays rather than solid-state switching. It integrates natively with Schneider inverters and batteries, which is its main advantage, and it is the panel most easily quoted as part of a Schneider solar and battery package rather than on its own. Hardware runs about 3,000 to 5,150 USD before installation, and Schneider publishes few standalone installed prices because the product is usually sold inside a system.
Pros
- Up to 42 circuits with modular smart relays
- Native integration with Schneider solar and battery equipment
- Retrofits into standard modular enclosures in many cases
Cons
- Few installers publish a standalone installed price
- Least compelling if you are not buying Schneider solar or storage
Check today’s price on Amazon.
4. Lumin Smart Panel, best retrofit
Lumin is the answer when your existing panel is healthy and you want control without replacing it. It installs beside the panel you already have and manages 8 to 12 circuits with automatic load management, prioritising critical loads during an outage and shedding the rest. That makes it a good companion to a battery, and it is the fastest install of the panels here because it does not involve a full swap. Installed prices run about 3,000 to 8,000 USD depending on how many circuits are managed, and it pairs with major battery brands including Tesla, Enphase, SolarEdge and FranklinWH.
Pros
- Installs beside your existing panel, no full replacement
- 8 to 12 managed circuits with automatic load management
- Faster, cheaper install than a full smart panel
Cons
- Only the managed circuits are controlled
- Sold through installers with few published hardware prices
Check today’s price on Amazon.
5. Eaton Brightlayer with Span software, best for Eaton households
Eaton now sells panels running Span’s software, which means you get the same every-circuit metering and control as a Span panel through Eaton’s distribution and installer channel. It is worth a look if your electrician prefers Eaton equipment or if you are buying into an Eaton system, because the software experience is the same and the panel hardware is Eaton’s. Pricing is quoted through a Span authorized installer rather than published at a single figure, so it is a get-a-quote option rather than a buy-now one.
Pros
- Same every-circuit control as a Span panel
- Available through Eaton’s distribution and installer network
- Good fit if your electrician is an Eaton house
Cons
- No single published price, quoted per installation
- Requires a Span authorized installer for the warranty
Check today’s price on Amazon.
How to choose the best smart panel
Start with the state of your current panel, because that decides the category. If the panel is old, undersized, recalled or you are adding a service upgrade anyway, a full replacement like the Span or the Schneider makes sense. If the panel is healthy and you simply want control and monitoring, a retrofit like the Lumin or a modular approach like the Leviton is cheaper and less disruptive.
Then decide what you want to control, because that decides the architecture. If you want to shed individual circuits during a battery outage, or manage an EV charger against the rest of the house, you need per-circuit switching, which is what a full smart panel or a set of smart breakers gives you. If you only want to see where the energy goes, an energy monitor clamped onto the mains does most of it for a few hundred dollars, and our balcony solar guide covers the generation side.
Count the circuits and the cost per circuit, because the headline price hides it. A full panel with 32 or 40 circuits gives you control everywhere for one price. A modular panel with two smart breakers and a panel with twelve are different purchases, so ask for the quote with the breaker count you actually need. A retrofit managing 8 to 12 circuits is usually the cheapest way to get the behaviour people actually want.
Check the ecosystem, because the panel should talk to what you already own. Span integrates natively with Tesla, Enphase, SolarEdge and FranklinWH batteries, Schneider integrates best with Schneider equipment, and Lumin pairs with most major batteries. Buying a panel that does not talk to your battery or your inverter means two apps and no automatic load shedding, which is most of the point.
Finally, get two installation quotes and ask about the permit, because this is real electrical work. A detailed 2026 comparison at energybs.com/green-living/efficiency/best-smart-electrical-panel-2026 tracks the hardware prices, the installed ranges and the circuit counts of the leading panels, and it is a good baseline before you talk to an electrician.
Living with a smart panel
Label every circuit during commissioning, because an unlabelled smart panel is a guessing game. Go through the list with the installer, switch each circuit on and confirm the mapping in the app, and rename anything vague. The twenty minutes spent here saves years of confusion.
Set the shedding rules once and then leave them. The point of a smart panel is that it reacts faster than you can during an outage, so decide in advance which circuits are critical, which are sheddable and which are optional, and let the panel enforce it. Review the list after a year, because your usage changes and a circuit you thought was essential may not be.
Do not turn circuits off for fun. It is tempting to switch things from the app, but a refrigerator, a freezer, a sump pump or a medical device should stay on, and a furnace or a heat pump can be damaged by an awkward power cycle. Use the control for load management and for diagnosing a faulty circuit, not as a light switch.
Keep the app updated and the panel accessible. Firmware updates bring new integrations and safety fixes, and a panel buried behind stored boxes is a panel you cannot reach in an emergency. Check the breaker status occasionally, and if a circuit trips repeatedly, investigate rather than resetting it.
Pair the panel with a battery and solar if you can, because that is where the control pays. A smart panel managing a battery and an EV charger against the rest of the house is a genuinely useful system, and our guide to the best whole-home backup batteries covers the storage side. If you only want visibility rather than control, an energy monitor is the cheaper route.
Frequently asked questions
Frequently Asked Questions
6Do I need an electrician for a smart circuit breaker panel?
Yes. A smart panel or a retrofit controller connects to your consumer unit and usually needs a permit, a utility disconnect and a licensed electrician. This is not a DIY job, and the warranty on a Span panel depends on installation by an authorized installer.
What is the difference between a smart panel and a smart breaker?
A smart panel replaces the whole box and meters and controls every circuit. A smart breaker is a single intelligent breaker fitted into a conventional panel, so only the circuits you fit are controlled. Smart breakers are cheaper to start and smart panels are more complete.
Can a smart panel save me money?
Usually not on its own. The value is control: shedding loads during a battery outage, managing an EV charger against the rest of the house, and seeing which circuits use the most. The savings come from the battery, the solar and the tariff, with the panel making them work together.
Will a smart panel work with my existing solar and battery?
Often yes. Span integrates with Tesla, Enphase, SolarEdge and FranklinWH, Lumin pairs with most major batteries, and Schneider integrates best with its own equipment. Check the specific model and the integration list before you buy, because a panel that cannot talk to your battery loses most of its value.
How much does a smart panel cost installed?
In late 2026, a retrofit like Lumin ran about 3,000 to 8,000 USD installed, a modular Leviton about 3,500 to 7,500 USD depending on the breaker count, and a full replacement like Span about 6,500 to 10,000 USD. Regional labour and the job scope move these figures a long way.
Do smart panels need an internet connection?
For the app and the remote control, yes. Local control and the automatic load shedding usually continue if the internet drops, but you lose remote access and some integrations. A few systems log data locally and sync later.
The bottom line
Buy the Span Smart Panel if you are replacing the panel anyway and you want every circuit metered and controlled. It is the most complete product here, the integration list is the broadest, and the 10-year warranty is the strongest. Expect about 6,500 to 10,000 USD installed, and accept that it is a real electrical job with a permit.
The Leviton Smart Load Center is the better fit if your panel is sound and you want to start small, because you add smart breakers one circuit at a time and any licensed electrician can fit them. The Lumin is the pick if you want control without replacing the panel at all, and the Schneider is the one to choose inside a Schneider solar and battery system.
Before you spend that much, be honest about whether you want control or just visibility. If it is visibility, an energy monitor costs a few hundred dollars and clamps onto the mains in an afternoon. If it is control, a smart panel is the right tool, and pairing it with a battery and solar is where the money actually does something useful.
Leave a Comment